I managed to get out for a sneaky camp on Monday night. The forecast was some heavy rain. I managed to pitch before the rain but in the event there were only a few light showers. Looking at the rain radar, it passed further south. However, I was able to take some moody cloud photos. It was good to use the Notch Li again. I’ve done a couple of things to it which I will share in another post.
I’ve added four pegging points to the door panels on the Notch using some Tread Lite Gear DCF patches https://www.treadlitegear.co.uk/pair-tread-lite-gear-fully-bonded-dyneema-composite-fabric-dcf-stick-on-patches-515-p.asp They should help to minimise panel flap. Very easy to do.
There’s not a lot of storage space in the inner tent in a TT Notch (plenty in the porches) so I used a bit of lateral thinking. I spotted a triangular gear loft from Big Agnes and thought I might be able to adapt it for the Notch ( https://www.ultralightoutdoorgear.c…-tent-accessories-c315/tent-gear-lofts-p13534 )
It fits rather well!
I had to sew a grosgrain loop at the end on the inner tent. I extended two cords to the pole apex glove hooks on the inner. Because the inner ends are secured to the pitchlok apex by elastic you wouldn’t want to put anything too heavy in the gear loft as it would drag the inner down a bit, but it will be handy for lighter items that you don’t want to store on the floor. It doesn’t impede the door either.
No tent is perfect and no tent survives my roving eye for modifications. The Tarptent Notch Li is no exception. Right from the start I want to emphasise that the Notch Li is fine without any tweaks and the changes I have made are from personal preference. So here we go!
New cords: this is something that many people do. On my Scarp and now my Notch, I’ve replaced the cordage at the ends with thicker 2.8mm MLD cord to prevent any slippage. Now, Tarptent say that the cord they supply won’t slip and it is different to the cord that they used to supply with the original Scarp, where I encountered problems. While I have no reason to doubt them, I’d rather be safe than sorry. I’ve also lengthened the cord, although in the picture, I actually think it is too long and will shorten it. I also added a sail ring for the bottom cord to slip through (not obvious from the picture) and a larger pull out loop of cord in case I use a large peg like an MSR Blizzard stake. The Notch (like the Scarp) puts quite a lot of strain on the end pegs so it pays to have substantial pegs at the ends.
Corner loops and kamsnap closure: I’ve added a loop on each corner so the bottom of the PitchLoc struts can be pulled down to the ground on uneven ground. Most of the time this won’t be an issue, but it adds no extra weight and makes sure the PitchLoc ends are absolutely stable. The PitchLocs are the key on many Tarptent tents to their stable structure. As I’ve said before, they are genius! The observant in the congregation will note I’ve added a kamsnap closure at the bottom of the velcro on ventilation flap. While I’m not sure it’s absolutely necessary, it will prevent any chance of a strong gust of wind loosening the closure. I’m a bit of a kamsnap fiend!
Extra door linelok: I mentioned in a previous post that it might be wise to treat the door zip with some care as it is light gauge and could get strained. One way of helping to alleviate this is to add another linelok. If you don’t want to add another linelok, then it would be easy to add a fixed loop to the existing grosgrain loop. However, I added a side-release linlok which means that you can not only adjust the tension but can also release the door panel without removing the cord from the peg. The grosgrain loop is just long enough to loop through the linelok fixing without requiring sewing. Brilliant!
To avoid losing the cord when it’s detached I’ve looped it on to the other door cord, similar to the way Colin Ibbottson has done on the Tramplite. Great idea! In the picture below, you can see that it also means that you can have the door unzipped but still have protection from both panels. I might attach a hook or clip at the base of the door zip as well, but this arrangement takes a lot of the strain off anyway.
Apex cords: at he two apexes I’ve used 1.5mm dyneema cord with Clam Cleat linloks. This arrangement is actually lighter than using 2mm or 3mm cord with the apex linelok. I’ve also made the cord longer. The apex cords are key to a rigid structure and unless camping in a very sheltered place, I’d always use them.
Mid ground sheet pullouts: at the mid points of the inner, there are webbing and shockcord pullouts at the base of the groundsheet to tension the middle of the inner. I’ve added a second pullout point where the groundsheet material meets the body fabric, using a kamsnap to secure it. To make it adjustable, I’ve added a length of thin shockcord which can be looped around a trekking pole handle. This pulls out the inner more effectively than just having a ground level pullout.
Having a kamsnap means it’s really easy to attach and adjust. I should’ve taken a picture inside the inner, but, believe me, it tensions the inner nicely and gives a bit more percieved space in the centre of the inner.
DCF pockets: there are some small pockets by the door but I’ve added a couple of pockets, one at either end. These were originally for my Laser Comp, but I’ve repurposed them for the Notch. Rather than sewing them, I’ve used safety pins to attach them. It’s a shame there’s no larger mesh pockets on the end panels as that would be ideal, especially as there’s very little spare space in the inner for gear.
Roof cord: I’m sure virtually everyone does this, a cord for hanging socks and lights. Mine’s adjustable with a cord lock. I will shorten it a bit.
Pole apex cords: in the picture above, the yellow cord is for a lantern, clothes or a food bag. The orange cord is to secure a trekking pole in “handle up” mode.
Although I bought the trekking pole adapters from Tarptent, they don’t work very well with Leki poles. This arrangement is almost as good and is simpler and lighter. It also means I have the option of tips up or handles up. Both cords are simply looped through the grosgrain at the apex that has the grommet for pole tips in the apex. You can see from the picture that I’ve also added zip puller on the fly door to make it easier to open. I’ve not bothered on the inner.
None of these mods are essential and the Notch Li is a good tent in its delivered condtion. However, for me, I think the mods add a bit to the original design. I hope you find them interesting!
A brief overnighter is hardly a good test but I thought I’d pass on some brief thoughts on the new gear I used recently.
Tarptent Notch Li
At around 600g, the Notch Li is astonishingly light for a proper two skin tent. I’ve made some minor tweaks which I will share in another post. It’s extremely easy and quick to pitch. Although you only need four pegs in theory, in practice you need six as the apex guys are needed to give it a robust structure. There was a modest breeze so it was hardly testing conditions but with the apex guys and pitchloc ends it’s a pretty solid structure.
In common with most trekking pole tents, there’s a bit of a gap between the hem of the fly and ground, so it was a bit more draughty than say the Scarp. I guess it’s a bit swings and roundabouts as a bit more air flow helps to mitigate condensation. With a fresh breeze condensation wasn’t an issue anyway. There is a small vent above both doors and the end panels can be opened so there are plenty of venting options.
While I much prefer zipped doors, the zips do feel a little fragile, so I think it would be wise to take care. I have put a side release line lok on either door panel that has just a grosgrain loop so it is feasible in calm conditions to have the zip open (something that Colin Ibbottson recommends on the Tramplite shelter to help with longevity). I might sew a buckle clip at the base of the door too.
In terms of room, the inner is quite compact. There’s not a huge amount of room for gear but it is reasonably long so some stuff can be stowed at either end. A modest amount can be stored at the mid point, but I put most of my gear in one porch. The porches are a decent size, so there is space to store things. The only thing to be careful with is rain might get blown under the fly sheet.
The flysheet seems to be lighter weight DCF than say the Tramplite, but the groundsheet is heavier and feels robust, which seems to be a good compromise. The solid inner fabric is thinner than the stuff they use in the Scarp and has a slight green tinge to it. I like it and wonder how much weight they could save on the Scarp if they used it. As an aside, the solid inner is marginally lighter than the mesh alternative. The inner pockets by the door are ok, but I think they’ve missed a trick by not putting them at the ends.
Overall, I’m pretty pleased with it. It feels like a decently robust mountain tent. It has a small footprint, making it ideal for summit camping. At 600g it’s astonishingly light for such a robust tent. The small inner will take a little getting used to, but not a major issue with a decent amount of porch space.
Nemo Tensor Alpine sleeping mat
At 475g the Tensor is 115g heavier than my Thermarest X-Lite, but is slightly larger and marginally warmer. It has a different structure and is less noisy to sleep on. I found it more comfortable to sleep on, partly because it doesn’t taper as much and partly because it feels more supportive. It didn’t deflate at all in the night and the valve makes it much quicker to deflate in the morning. I couldn’t tell any difference in insulation. It packs down small. Overall I like it for the extra comfort over the X-Lite, but it’s not a clear cut winner, just a bit different.
Atom Packs Mo 50
This was the first outing for the Mo. Until I walk a few days with it, I can’t give a definitive judgement, but it feels really comfortable. It just feels right. When packing, it is a little slim compared with my GG Mariposa, and is definitely smaller, so a little more care is needed in packing. It feels very robust. The side pockets are big enough for a tent or two water bottles. The stretch pocket is much more robust than on many packs. I like the rolltop closure and the Y strap.
All in all it’s a really well designed and made pack. I wish I’d bought the 60 for a little more space, but if I’m careful it should be big enough for multi-day trips. The Y strap means that I could put a stuff sack on top to increase volume. My pack weight was around 9kg with water and food and it carried that easily.
Mountain Equipment Kinesis trousers
I changed into these when I had camped and they were brilliant for the chilly weather. They are very light at 220g. The fleecy liner is lovely and soft but not too warm. The thigh vents are useful but I didn’t need them. I slept in them too and they kept me warm in the subzero overnight temperatures. They have a little bit of stretch which makes them great in the tent. They pack down quite small into one pocket.
It’s a shame ME have stopped making them but there are two new versions: one is like tracksuit bottoms and a bit lighter, the other is a heavier weight trouser with reinforcement patches. I prefer mine as they are are a good compromise between a usable and reasonably smart trouser but not overkill.
We had a few days in Buxton. It gave me the opportunity to explore Burbage Edge and the Goyt Valley. It’s a rather lovely part of the Peak District. It wasn’t too crowded but I suspect it gets busy in the summer.
As always I was on the lookout for potential places to camp. The Goyt Valley has some spots but I imagine there are too many people around and possibly the park rangers patrol it.
There are a couple of spots on the ridge of Burbage Edge but I spotted a nice place a little way away from the Edge. I camped at 7pm and only one person passed me by.
Inevitably being so close to Buxton and roads there was a little bit of traffic noise carried on a cold Easterly breeze. Fortunately it wasn’t particularly intrusive. The night was pretty cold and the temperature fell to below freezing in the tent. There was ice on the tent and frost on the ground in the morning.
I was up just in time to see sunrise. It was pretty chilly, so I made a cup of tea and packed. Instead of going straight back to Buxton, I walked along the Edge, past the trig point and down to Bishop’s Lane.
It was good to get out again and it gave me an opportunity to try out my new Tarptent Notch Li. More on that another time.